One of the balancing acts most owners will face daily is the cost vs payoff and durability on any home improvements they do. Many homeowners realize that using tin ceiling tiles will add an old world contemporary beauty to any home. Typically older tiles are felt to have been constructed better than their newer counterparts, though mass produced panels are often inexpensive and just as easy to install.
The older tin ceilings are making a huge comeback in today's building sights. The older vintage tiles removed from remodeled homes are selling at an all time premium. Many people find they have much better luck ordering their new panels and installing them themselves. Installing older ones and newer ones follow basically the same process from start to finish.
It is typically best to seal your ceiling with a good quality primer and let it dry completely. Plywood is then nailed or screwed to it to form a base for the tiles. Sometimes lathing can be used, but plywood is stronger and has better holding power to the ceiling. It is critical to make sure the entire roof is covered and that the plywood is attached to your joists not just the drywall.
One of the largest differences from better looking jobs and a poor looking jobs are when the panels are perfectly square to one another down the middle of the ceiling. Most rooms are not constructed as squares. Marking them out down the middle of the room with a line is a good way to make a reference point. Make sure it is visible as this is the point to start your panels.
After your center line is marked down it is time to install the cornice. Many cornices have slightly flanged edges along one side. This is generally the side that is covered by the ceiling panels. The edges are nailed to the plywood. Newer cornices also use long aluminum strips nailed to your wall to help support them.
It is often a good idea to try laying out any panels on the your floor first before you attach them to the roof. This will give you an idea of how they look and makes it much easier to adjust the layout. It is always easier to move them up from the floor to the roof as well.
When you are starting to transfer the tiles from your floor to your roof, tacking nails are commonly used to attach them. They are a little longer than normal so they can be removed easily with your pliers if there are any mistakes made. When they are locked in place where they look correct, systematically go over them using finish nails.
Work from the center out to the edges. Take the time to make sure any laps are facing away from doorways so they are less noticeable. When you are done, install your border pieces and any accessories or light fixtures you have left. Now you can stand back to admire the new tin ceiling tiles you just installed.
The older tin ceilings are making a huge comeback in today's building sights. The older vintage tiles removed from remodeled homes are selling at an all time premium. Many people find they have much better luck ordering their new panels and installing them themselves. Installing older ones and newer ones follow basically the same process from start to finish.
It is typically best to seal your ceiling with a good quality primer and let it dry completely. Plywood is then nailed or screwed to it to form a base for the tiles. Sometimes lathing can be used, but plywood is stronger and has better holding power to the ceiling. It is critical to make sure the entire roof is covered and that the plywood is attached to your joists not just the drywall.
One of the largest differences from better looking jobs and a poor looking jobs are when the panels are perfectly square to one another down the middle of the ceiling. Most rooms are not constructed as squares. Marking them out down the middle of the room with a line is a good way to make a reference point. Make sure it is visible as this is the point to start your panels.
After your center line is marked down it is time to install the cornice. Many cornices have slightly flanged edges along one side. This is generally the side that is covered by the ceiling panels. The edges are nailed to the plywood. Newer cornices also use long aluminum strips nailed to your wall to help support them.
It is often a good idea to try laying out any panels on the your floor first before you attach them to the roof. This will give you an idea of how they look and makes it much easier to adjust the layout. It is always easier to move them up from the floor to the roof as well.
When you are starting to transfer the tiles from your floor to your roof, tacking nails are commonly used to attach them. They are a little longer than normal so they can be removed easily with your pliers if there are any mistakes made. When they are locked in place where they look correct, systematically go over them using finish nails.
Work from the center out to the edges. Take the time to make sure any laps are facing away from doorways so they are less noticeable. When you are done, install your border pieces and any accessories or light fixtures you have left. Now you can stand back to admire the new tin ceiling tiles you just installed.
About the Author:
You can visit the website www.antiqueceilings.com for more helpful information about How To Install Tin Ceiling Tiles On Your House
No comments:
Post a Comment